FordEscape2011Overview/ford/escape/2011/base/

2011 Ford Escape

Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2011 Escape.

Body SUVTransmission Automatic 6-spd

The 2011 Ford Escape is an SUV equipped with a six-speed automatic transmission and EPA-estimated fuel economy of 20/26/22 mpg, requiring 5.3 quarts of 5W-20 API oil for routine service. Within the nameplate’s 2000–2024 complaint history, this model year registers 1,312 owner grievances—far exceeding the 2000 low of five yet remaining well below the 2013 high of 2,744—with steering cited as the primary concern alongside three recalls. That volume positions the 2011 model as a mid-spectrum entry in the Escape’s reliability record, showing significant defect reporting that falls short of the series peak but exceeds the relative stability of the earliest production years.

Model year202620252024202320212020201920182011

Quick specs

Fluid capacities, tune-up values and fuel economy at a glance.

Engine oil capacity5.3 qtOEM · verified
Engine oil type5W-20 APIOEM · verified
Lug nut torque100 ft-lbsOEM · verified
EPA fuel economy20/26/22 mpgEPA · verified

Fitment & sizes

Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.

From the factory this vehicle uses a BCI 96R Gas · 590 Gas CCA battery. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.

Battery groupBCI 96R Gas · 590 Gas CCAOEM · verified
Tire sizeP235-70R16OEM · verified

Full specifications

Engine, drivetrain, dimensions and economy.

Engine & drivetrain NHTSA vPIC

TransmissionAutomatic 6-spd

Dimensions & weight NHTSA vPIC

Overall length174.8 in
Overall width71.3 in
Overall height68.1 in
Wheelbase103.1 in
Curb weight3547 lb
Track (front / rear)61.4 / 60.2 in
Weight distribution (front / rear)59/41

Ratings & economy EPA / vPIC

EPA city / highway / combined20 / 26 / 22 mpg
DrivetrainAll-Wheel Drive
Recommended fuelRegular Gasoline

Performance & power Independent road tests

0–60 mph, quarter-mile, horsepower and torque from independent road tests.

Independent road tests for the Escape of this era, listed by trim and engine — this page spans more than one engine, so no single horsepower figure is shown.

5.7–11.0 sec0–60 mph (tested)quickest 5.70 sec — 2020 Titanium 2.0 EcoBoost
YearTrim / engine0–60¼ mileHPDrivetrain
2013Titanium EcoBoost 2.0L Turbo I-46.80 sec15.20 sec240 hpAWD
2013Titanium EcoBoost 2.0L Turbo I-47.00 sec15.30 sec240 hpAWD
2013SE EcoBoost 1.6L Turbo I-48.90 sec16.70 sec178 hpFWD
2013SE EcoBoost 1.6L Turbo I-49.00 sec16.70 sec178 hpFWD
2013SEL EcoBoost 1.6L Turbo I-49.10 sec16.90 sec178 hpAWD
2008XLT V6 3.0L V69.00 sec16.90 sec200 hpAWD
2008Limited V6 3.0L V69.50 sec17.30 sec200 hpAWD
2014SE EcoBoost 1.6L Turbo I-48.20 sec16.30 sec178 hpFWD

Service quick specs OEM factory data

Capacities, torques and tune-up values from the factory service manual.

This engine holds 5.3 qt of 5W-20 API engine oil, DOT 3 brake fluid. Torque lug nuts to 100 ft-lbs, the oil drain plug to 18.0 ft-lbs. The firing order is 1-4-2-5-3-6. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.

Lubricants & capacities

Automatic Transmission FluidFord Mercon LV
Automatic Transmission Fluid Capacity9
Brake FluidDOT 3
Engine CoolantUSE FORD PREMIUM GOLD COOLANT
Engine Oil5W-20 · API
Engine Oil Capacity5.3 qt
Engine Oil5W-20 · API
Engine Oil Capacity6.0 qt

Engine torques

Camshaft Bearing/Carrier Cap Bolts or Studs7 ft-lbs
Engine Flywheel Bolts59 ft-lbs
Intake Manifold to Engine Bolts13.3 ft-lbs
Engine Oil Pan Drain Plug18.0 ft-lbs
Oil Pump to Cylinder BLock Bolts/Studs7 ft-lbs

Chassis torques

Lug Nuts100 ft-lbs
Transfer Case Fill Plug25.0 ft-lbs
Front Wheel Hub222 ft-lbs
Rear Wheel Hub221 ft-lbs

Ignition

Cylinder Firing Order1-3-4-2
Cylinder Firing Order1-4-2-5-3-6
Spark Plug ManufacturerMotorcraft

Battery & A/C

RefrigerantR134a
Refrigerant Capacity1.57 lbs
Oil GroupPAG
Oil Type46
Oil Capacity5.00 oz
RefrigerantR134a
Refrigerant Capacity2.00-3.00 lbs
Standard BCI Group Number96R Gas

Service checks

Pressure Test21 psi
Radiator Cap Pressure Relief17-21 psi
Thermostat Opening Temperature194 °F
Pressure Test21 psi
Radiator Cap Pressure Relief17-21 psi
Thermostat Opening Temperature183-190 °F
Key ON Engine OFF (KOEO)55
Key ON Engine OFF (KOEO)55

Brakes

Torque to Knuckle129 ft-lbs
Torque Caliper to Bracket18 ft-lbs
Minimum Pad ThicknessFront: 0.118; Rear: 0.039 in
Rotor Runout Limit0.002 in
Rotor Discard at or Under0.944 in
Drum Discard at-or-over10.09

Multi-step torque procedures OEM · verified

Camshaft Bearing/Carrier Cap Bolts or Studs — tightening sequence 1 stages
1Tighten all bolts finger tight., Step 25 ft. lbs
Connecting Rod (Large End) Bearings — tightening sequence 1 stages
121 ft. lbs., Step 2: 9021 ft. lbs
Connecting Rod (Large End) Bearings — tightening sequence 1 stages
117 ft. lbs., Step 2: 3217 ft. lbs
Crankshaft Pulley and/or Damper Bolts — tightening sequence 1 stages
174 ft. lbs., step 2: 9074 ft. lbs
Crankshaft Pulley and/or Damper Bolts — tightening sequence 1 stages
189 ft. lbs., step 2: 360 degrees, step 4: 37 ft. lbs., step 5: 9089 ft. lbs
Cylinder Head — tightening sequence 6 stages

Prep Do not reuse old bolts. Coat new bolts with the specified engine oil.

130.0 ft. lbs.30 ft. lbs
290 degrees90 degrees
3Loosen bolts 360 degrees360 degrees
430 ft. lbs.30 ft. lbs
590 degrees90 degrees
690 degrees90 degrees
Engine Flywheel Bolts — tightening sequence 1 stages
137 ft. lbs., Step 2: 59 ft. lbs., Step 3: 8337 ft. lbs
Exhaust Manifold to Cylinder Head Bolts — tightening sequence 1 stages
135 ft. lbs., Step 2: 3535 ft. lbs
Intake Manifold to Engine Bolts — tightening sequence 1 stages
17.4 ft. lbs., step 2: turn 457.4 ft. lbs
Exhaust Manifold to Cylinder Head Bolts — tightening sequence 1 stages
1Install 6 new exhaust manifold stud9 ft. lbs
Main Bearings — tightening sequence 1 stages
14 ft. lbs., Step 2: 18 ft. lbs., Step 3: 904 ft. lbs
Oil Pump to Cylinder BLock Bolts/Studs — tightening sequence 1 stages
17 ft. lbs., Step 2: 157 ft. lbs

Factory maintenance schedule OEM · verified

Normal service, condensed from the factory interval matrix.

Under the factory schedule, replace the spark plugs every 100,000 mi; coolant every 50,000 mi. The big-interval services (every 50,000 mi for coolant, and the transmission fluid) are the ones owners most often skip — on a lower-mileage example, assume the original fluids are still in it and check them first.

At 10,000 miCabin Air Filter (inspect)
Every 10,000 miBrake System (inspect) · CV Joint Boot (inspect) · Cabin Air Filter (inspect) · Driveshaft (inspect) · Driveshaft U-Joint (inspect) · Engine Coolant System (inspect fluid level)
Every 20,000 miAccessory Drive Belt (inspect) · Cabin Air Filter (replace) · Cabin Air Filter (inspect)
Every 30,000 miEngine Air Filter Element (replace) · Temperature Controlled Seat Air Filter (replace)
Every 50,000 miEngine Coolant System (drain, flush & refill)
At 100,000 miAccessory Drive Belt (inspect) · Engine Coolant System (drain, flush & refill)
Every 100,000 miSpark Plugs (replace)
At 150,000 miDrive Belt (replace) · Transmission Assembly (drain & refill)

Reliability & federal safety record

Owner-reported issues, recalls, investigations and service bulletins on record with NHTSA — an unfiltered look at what owners actually experience.

The 2008–2012 Escape generation saw its worst complaint volume in 2008 (2,415 complaints, 6 recalls), with elevated levels persisting through 2010 (2,127 complaints, 5 recalls) before declining into 2011. At 1,312 complaints and 3 recalls, the 2011 model year represents a meaningful drop—roughly 38% fewer complaints than 2010 and the lowest recall count in this generation's arc—suggesting Ford had begun resolving the issues that plagued the earlier years of the cycle. By 2012, complaints fell further to 598 with just 2 recalls, confirming a clear downward trend that places 2011 in the improving tail end of the generation. However, the 2011's top complaint areas remain notable: Steering dominates at 350 complaints, followed by Power Train (124), Fuel/Propulsion System (117), and Vehicle Speed Control (70), alongside 38 crash complaints and 7 fire complaints—figures that indicate residual safety-relevant concerns had not been fully engineered out. The data does not specify root causes for these areas, but the concentration in steering and speed control warrants particular scrutiny during a pre-purchase inspection. **Takeaway:** The 2011 Escape is a reasonable buy within this generation—statistically better than 2008–2010—but only if a qualified technician specifically verifies steering system integrity and throttle/speed-control function, given those areas' outsized complaint presence.

3
Open recalls
NHTSA campaigns
49
Service bulletins
Manufacturer communications
4
ODI investigations
Office of Defects Investigation
1,312
Owner complaints
38 involved a crash · 7 a fire
NHTSA crash-test rating federal NCAP · out of 5 stars
Overall★★★★★
Frontal★★★★★
Side★★★★★
Rollover★★★★★

Owner complaints filed with NHTSA, by component

All 1,312 complaints on record, top 8 components.

Steering350
Power Train124
Fuel/Propulsion System117
Vehicle Speed Control70
Engine64
Vehicle Speed Control,Fuel/Propulsion System43
Power Train,Engine42
Vehicle Speed Control,Engine38

Source: NHTSA Office of Defects Investigation complaint database.

Recalls NHTSA · verified

Showing 2 of 3 campaigns on record for this vehicle.

16V777000Fuel System, Gasoline:Delivery:Fuel PumpReported 26/10/2016

Ford Motor Company (Ford) is recalling certain model year 2010-2012 Ford Escape vehicles manufactured February 26, 2009, to April 29, 2012, and 2010-2011 Mercury Mariner vehicles manufactured February 25, 2009, to… Remedy: Ford will notify owners, and dealers will replace the FDM flange with one that has a redesigned fuel supply port, free of charge. Remedy parts are currently unavailable. Interim…

15E045000Suspension:Front:Wheel BearingReported 03/06/2015

The Timken Company (Timken) is recalling certain aftermarket front wheel bearings, part number 510072, sold from January 22, 2015, to May 21, 2015, to be used as service parts on 2001-2012 Ford Escape, 2001-2011 Mazda… Remedy: Timken has begun notifying distributors who will offer purchasers replacement wheel bearings, free of charge. The recall began on May 21, 2015. Owners may contact Timken customer…

Technical service bulletins NHTSA · verified

Showing 5 of 49 bulletins on record with NHTSA.

BulletinDateComponentSummary
SSM 546012026-02-23Electrical SystemFord and Lincoln vehicles equipped with wired keyless entry keypad systems and accessory…
SSM 524762024-04-24EquipmentAll accessory stick-on keyless entry keypads come with a wallet card containing the…
SSM 515362023-04-04StructureFor 2000-2024 Ford and Lincoln vehicles, swapping a module from a vehicle for diagnosis…
DOR-M9J4S-072020-06-03Engine And Engine CoolingThese SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication…
DOR-M3J3F-072020-06-03Engine And Engine CoolingThese SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication…

Common OBD-II trouble codes

The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.

P0420
Catalyst system efficiency below threshold — Bank 1
P0300
Random / multiple cylinder misfire detected
P0171
System too lean — Bank 1
P0455
Evaporative emission system leak detected — large leak
P0128
Coolant thermostat below regulating temperature
P0442
Evaporative emission system leak detected — small leak

VIN tools

Decode factory build data for a specific vehicle by VIN.

VIN
Decode a VIN to confirm the transmission and build data for a specific Escape. OEM
Build data
Plant, GVWR class, engine and body data for any 17-character VIN.
Recalls
Check open recall campaigns against a specific vehicle by VIN.

Vehicles with shared specs

Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.

Reference guides

Cross-vehicle references for the kinds of data on this page.

Frequently asked

How much oil does the 2011 Escape take?

5.3 qt of 5W-20 API MEETING FORD SPECIFICATION WSS-M2C945-A, per the factory manual.

Does the 2011 Escape have open recalls?

NHTSA lists 3 recall campaign(s) for this model year. Check your specific vehicle by VIN.

What gas mileage does the Escape get?

EPA figures are 20 city / 26 highway / 22 combined mpg.