Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2013 SL65 AMG.
Fluid capacities, tune-up values and fuel economy at a glance.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 48 · 760 CCA battery, OE oil filter 1370110180. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 1370110180 alt 2751800009 |
| Engine air filter | 2750940204 |
| Fuel filter | 2214701190 |
| Battery | 0019828208 alt 2115410001 |
| Front wiper blades | 2318201045 |
| Thermostat | 1372030180 |
Engine, drivetrain, dimensions and economy.
| Overall length | 182.3 in |
| Overall width | 74 in |
| Overall height | 51.2 in |
| Wheelbase | 101.6 in |
| Curb weight | 4299 lb |
| Track (front / rear) | 62.6 / 62.6 in |
| Weight distribution (front / rear) | 50/50 |
Capacities, torques and tune-up values from the factory service manual.
This engine DOT 4 brake fluid. Torque lug nuts to 96 ft-lbs, the oil drain plug to 22.1 ft-lbs. The firing order is 1-12-5-8-3-10-6-7-2-11-4-9.
| Automatic Transmission Fluid | ATF |
| Automatic Transmission Fluid Capacity | 8.5-10.5 |
| Brake Fluid | DOT 4 |
| Exhaust Manifold to Cylinder Head Bolts | 11 ft-lbs |
| Intake Manifold to Engine Bolts | 6.0 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 11.0 ft-lbs |
| Engine Oil Pan Drain Plug | 22.1 ft-lbs |
| Lug Nuts | 96 ft-lbs |
| Cylinder Firing Order | 1-12-5-8-3-10-8-7-2-11-4-9 |
| Cylinder Firing Order | 1-12-5-8-3-10-6-7-2-11-4-9 |
| Refrigerant | R134a |
| Standard BCI Group Number | 48 |
| Standard BCI Cranking Performance | 760 cca |
| Optional BCI Group Number | V4 |
| Optional BCI Cranking Performance | 520 cca |
| Engine Compression | 174 |
| Engine Compression | 174-203 psi |
| Torque to Knuckle | 133 ft-lbs |
| Rotor Nominal Thickness From | 1.417 in / 1.024 in |
| Rotor Nominal Thickness To | 1.417 in / 1.024 in |
| Rotor Minimum Machining | 1.323 in / 0.964 in |
| Rotor Discard at or Under | 1.299 in / 0.944 in |
| 1 | 202 ft. lbs., step 2: 90 | 202 ft. lbs |
| 1 | 3 ft. lbs., step 2: tighten bolts 180 | 3 ft. lbs |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.