Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2010 S63.
The 2010 Mercedes S63 takes 9.9 qt of 0W-30 engine oil.
Fluid capacities, tune-up values and fuel economy at a glance.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 49 · 850 CCA battery, OE oil filter 1561840361. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 1561840361 alt 0001803009 |
| Engine air filter | 1560940504 |
| Fuel filter | 2214702090 |
| Spark plug | 0041593903 |
| Battery | 0019828208 alt 000982960864 |
| Front wiper blades | 2218201300 |
| Thermostat | 1562030380 alt 1562030475 |
| Cabin air filter | 2218300718 |
Engine, drivetrain, dimensions and economy.
| Overall length | 193.3 in |
| Overall width | 73.6 in |
| Overall height | 54.7 in |
| Wheelbase | 112.2 in |
| Curb weight | 4211 lb |
| Track (front / rear) | 63 / 61.4 in |
| Weight distribution (front / rear) | 52/48 |
Capacities, torques and tune-up values from the factory service manual.
This engine holds 9.9 qt of 0W-30 / 5W-30 / 0W-40 engine oil, DOT 4 brake fluid. Torque lug nuts to 110 ft-lbs, the oil drain plug to 22.1 ft-lbs. The firing order is 1-5-4-2-6-3-7-8.
| Automatic Transmission Fluid | ATF |
| Automatic Transmission Fluid Capacity | 8.0-11.0 |
| Brake Fluid | DOT 4 |
| Differential Gear Oil Capacity | 2.5 Pints |
| Engine Coolant | USE ONLY COOLANT MEETING MB SHEET 325.0 |
| Engine Oil | 0W-30 · 5W-30 · 0W-40 · 5W-40 · 5W-50 |
| Engine Oil Capacity | 9.9 qt |
| Exhaust Manifold to Cylinder Head Bolts | 16 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 16.0 ft-lbs |
| Engine Oil Pan Drain Plug | 22.1 ft-lbs |
| Lug Nuts | 110 ft-lbs |
| Cylinder Firing Order | 1-5-4-2-6-3-7-8 |
| Cylinder Firing Order | 1-5-4-2-6-3-7-8 |
| Refrigerant | R134a |
| Refrigerant Capacity | Less rear A/C, 2.36; w/rear A/C, 2.60. lbs |
| Oil Group | PAG |
| Oil Type | 46 |
| Oil Capacity | 3.72 oz |
| Standard BCI Group Number | 49 |
| Standard BCI Cranking Performance | 850 cca |
| Engine Compression | 174-232 psi |
| Torque Caliper to Bracket | 21 ft-lbs |
| Torque to Knuckle | 81 ft-lbs / 133 ft-lbs |
| Rotor Nominal Thickness From | 1.024 in / 1.417 in |
| Rotor Nominal Thickness To | 1.024 in / 1.417 in |
| Rotor Minimum Machining | 0.945 in / 1.338 in |
| Rotor Discard at or Under | 0.921 in / 1.315 in |
| 1 | 184 ft. lbs., step 2: 360 degrees, step 3: 147 ft. lbs., step 4: 180 | 184 ft. lbs |
| 1 | 5.9 ft. lbs., step 2: 7.4 | 5.9 ft. lbs |
| 1 | 7.4, Step 2 | 90 degrees |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.
9.9 qt of 0W-30, 5W-30, 0W-40, 5W-40 OR 5W-50, per the factory manual.