Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2007 R500.
The 2007 Mercedes R500 takes 9 qt of 0W-30 engine oil.
Fluid capacities, tune-up values and fuel economy at a glance.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 49 · 950 CCA battery. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Fuel filter | 2514700090 |
| Battery | 0019828208 |
| Front wiper blades | 2518200100 |
| Thermostat | 1122030076 alt 1122030275 |
Engine, drivetrain, dimensions and economy.
| Overall length | 203.5 in |
| Overall width | 75.6 in |
| Overall height | 65.4 in |
| Wheelbase | 126.8 in |
| Curb weight | 5004 lb |
| Track (front / rear) | 64.6 / 63.8 in |
| Weight distribution (front / rear) | 52/48 |
Capacities, torques and tune-up values from the factory service manual.
This engine holds 9 qt of 0W-30 / 5W-30 / 0W-40 engine oil, DOT 4 brake fluid. Torque the oil drain plug to 22.1 ft-lbs. The firing order is 1-5-4-2-6-3-7-8.
| Automatic Transmission Fluid | ATF |
| Automatic Transmission Fluid Capacity | 7.5-9.5 |
| Brake Fluid | DOT 4 |
| Differential Gear Oil Capacity | 2.3 Pints |
| Engine Oil | 0W-30 · 5W-30 · 0W-40 · 5W-40 · 5W-50 |
| Engine Oil Capacity | 9 qt |
| Intake Manifold to Engine Bolts | 15 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 12 ft-lbs |
| Intake Manifold to Engine Bolts | 15.0 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 12.0 ft-lbs |
| Engine Oil Pan Drain Plug | 22.1 ft-lbs |
| Cylinder Firing Order | 1-5-4-2-6-3-7-8 |
| Cylinder Firing Order | 1-5-4-2-6-3-7-8 |
| Refrigerant | R134a |
| Refrigerant Capacity | Less rear A/C, 2.14; w/rear A/C, 2.69. lbs |
| Oil Group | PAG |
| Oil Type | 46 |
| Oil Capacity | 3.72 oz |
| Standard BCI Group Number | 49 |
| Standard BCI Cranking Performance | 950 cca |
| Pressure Test | 20 psi |
| Radiator Cap Pressure Relief | 20.3 psi |
| Thermostat Opening Temperature | 185-192 °F |
| Engine Compression | 130-174 PSI. 21 maximum variation PSI. |
| Engine Compression | 130-174 psi |
| Torque Caliper to Bracket | 40 ft-lbs / 18 ft-lbs |
| Torque to Knuckle | STEP 1: 44, STEP 2: 45 DEGREES ft-lbs |
| Minimum Pad Thickness | Front: 0.079; Rear: 0.079 in |
| Rotor Nominal Thickness From | 1.26 in / 0.551 in |
| Rotor Nominal Thickness To | 1.26 in / 0.551 in |
| Rotor Minimum Machining | 1.181 in / 0.472 in |
| Rotor Discard at or Under | 1.157 in / 0.448 in |
| 1 | 148 ft. lbs., step 2: 90 | 148 ft. lbs |
| 1 | 60 inch lbs., Step 2: 22.0 ft. lbs., Step 3: 90 | 60 in |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.
9 qt of 0W-30, 5W-30, 0W-40, 5W-40 OR 5W-50, per the factory manual.