Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2006 R500.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 49 · 950 CCA battery. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Fuel filter | 2514700090 |
| Battery | 0019828208 |
| Front wiper blades | 2518200100 |
| Thermostat | 1122030076 alt 1122030275 |
Engine, drivetrain, dimensions and economy.
| Overall length | 203.5 in |
| Overall width | 75.6 in |
| Overall height | 65.4 in |
| Wheelbase | 126.8 in |
| Curb weight | 5004 lb |
| Track (front / rear) | 64.6 / 63.8 in |
| Weight distribution (front / rear) | 52/48 |
Capacities, torques and tune-up values from the factory service manual.
This engine DOT 4 brake fluid. Torque the oil drain plug to 22.1 ft-lbs. The firing order is 1-5-4-2-6-3-7-8.
| Automatic Transmission Fluid | ATF |
| Automatic Transmission Fluid Capacity | 7.5-9.5 |
| Brake Fluid | DOT 4 |
| Differential Gear Oil Capacity | 2.3 Pints |
| Intake Manifold to Engine Bolts | 15 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 12 ft-lbs |
| Engine Oil Pan Drain Plug | 22.1 ft-lbs |
| Cylinder Firing Order | 1-5-4-2-6-3-7-8 |
| Cylinder Firing Order | 1-5-4-2-6-3-7-8 |
| Spark Plug Gap | 0.031 in |
| Refrigerant | R134a |
| Refrigerant Capacity | 2.12 lbs |
| Oil Group | PAG |
| Oil Type | MB part number 0019890803 or equivalent |
| Standard BCI Group Number | 49 |
| Standard BCI Cranking Performance | 950 cca |
| Pressure Test | 20 psi |
| Radiator Cap Pressure Relief | 20.3 psi |
| Thermostat Opening Temperature | 185-192 °F |
| Regulated Fuel System Pressure (Without Vacuum) | 54.0-61.0 psi |
| Regulated Fuel System Pressure (With Vacuum) | 46.0-52.0 psi |
| Engine Compression | 169-203 psi |
| Torque Caliper to Bracket | 40 ft-lbs / 18 ft-lbs |
| Torque to Knuckle | STEP 1: 44, STEP 2: 45 DEGREES ft-lbs |
| Minimum Pad Thickness | Front: 0.079; Rear: 0.079 in |
| Rotor Nominal Thickness From | 1.26 in / 0.551 in |
| Rotor Nominal Thickness To | 1.26 in / 0.551 in |
| Rotor Minimum Machining | 1.181 in / 0.472 in |
| Rotor Discard at or Under | 1.157 in / 0.448 in |
| 1 | 148 ft. lbs., step 2: 90 | 148 ft. lbs |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.