Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2015 ML250.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI Battery group and CCA will vary by model options and region. Refer to the appropriate service information. · Battery group and CCA will vary by model options and region. Refer to the appropriate service information. CCA battery, OE oil filter 0199971745. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 0199971745 alt 0199971845 |
| Battery | 000982960864 alt 0019828208 |
| Front wiper blades | 166820104528 |
| Thermostat | 651200320064 |
| Cabin air filter | 1668300218 |
Capacities, torques and tune-up values from the factory service manual.
This engine DOT 4 brake fluid. Torque the oil drain plug to 22.1 ft-lbs. The firing order is 1-3-4-2. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Brake Fluid | DOT 4 |
| Fuel Tank Capacity | 26.4 gallons |
| Intake Manifold to Engine Bolts | 6.6 |
| Intake Manifold to Engine Bolts | 6.6 ft-lbs |
| Engine Oil Pan Drain Plug | 22.1 ft-lbs |
| Cylinder Firing Order | 1-3-4-2 |
| Refrigerant | R134a |
| Oil Group | PAG |
| Oil Type | 46 |
| Engine Compression | psi 333-435 / max variation 43 psi |
| Brake Caliper Bolt to Carrier Torque | Front: 41; Rear: 26 /; Front: 41; Rear: 26 |
| Brake Caliper Carrier to Hub Bolt Torque | Front: 59; Rear: 44 /; Front: 59; Rear: 44 |
| Minimum Pad Thickness | Front: 0.079; Rear: 0.079 Vehicle |
| Vented Rotor Minimum Thickness for Replacement | Front: 1.157; Rear: .764 |
| Vented Rotor Minimum Thickness after Refinish | Front: 1.181; Rear: .787 |
| 1 | 258.0 ft. lbs., Step 2: Back off 180 degrees, Step 3: 184.0 ft. lbs., Step 4: 30 | 258 ft. lbs |
| 1 | 184.0 ft. lbs., Step 2: Back off 180 degrees, Step 3: 147.0 ft. lbs., Step 4: 30 | 184 ft. lbs |
Prep If M12 bolts are longer than 227.50 mm the need to be replaced with new bolts. New M12 bolts have a length of 226.00 mm
| 1 | Bolts 1-10 | 7 ft. lbs |
| 2 | Bolt 13 | 15 ft. lbs |
| 3 | Bolt 12 | 15 ft. lbs |
| 4 | Bolts 1-10 | 37 ft. lbs |
| 5 | Bolt 13 | 15 ft. lbs |
| 6 | Bolt 12 | 15 ft. lbs |
| 7 | Bolts 1-10 | 90 degrees |
| 8 | Bolts 1-10 | 90 degrees |
| 9 | Bolts 1-10 | 90 degrees |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.