MercedesGLC63 AMG S2018Overview/mercedes/glc63-amg-s/2018/base/

2018 Mercedes GLC63 AMG S

Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2018 GLC63 AMG S.

Model year202120192018

Quick specs

Fluid capacities, tune-up values and fuel economy at a glance.

Lug nut torque111 ft-lbsOEM · verified

Fitment & sizes

Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.

From the factory this vehicle uses OE oil filter 0309970748. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.

OE service part numbers OEM · verified

Engine oil filter0309970748 alt 278180000990
Engine air filter177094000464
Spark plug0001590500
Battery0019828108
Front wiper blades2058204503
Thermostat1772008801
Cabin air filter1668300218

Service quick specs OEM factory data

Capacities, torques and tune-up values from the factory service manual.

Torque lug nuts to 111 ft-lbs. The firing order is 1-5-4-2-6-3-7-8. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.

Engine torques

Oxygen (O2S) Sensor Bolt(s)30.0 ft-lbs
Knock Sense (KS) Bolt(s)16.0 ft-lbs
Intake Manifold to Engine Bolts9.6 ft-lbs
Oil Pump to Cylinder BLock Bolts/Studs18.0 ft-lbs

Chassis torques

Lug Nuts111 ft-lbs

Ignition

Cylinder Firing Order1-5-4-2-6-3-7-8

Battery & A/C

Oil Type46
Oil Capacity2.80 oz
Oil GroupPAG

Service checks

Engine Compression189

Multi-step torque procedures OEM · verified

Connecting Rod (Large End) Bearings — tightening sequence 1 stages
144.0 inch lbs., Step 2: 22.0 ft. lbs., Step 3: 9044 in
Crankshaft Pulley and/or Damper Bolts — tightening sequence 1 stages
1148.0 ft. lbs., Step 2: 90148 ft. lbs
Crankshaft Pulley and/or Damper Bolts — tightening sequence 1 stages
1148.0 ft. lbs., Step 2: 90148 ft. lbs
Cylinder Head — tightening sequence 4 stages

Prep Do not reuse old bolts. Use new bolts coated with clean engine oil. Tighten all bolts to finger tight then continue on with the following procedure.

1Bolts 1-1130 ft. lbs
2Bolts 1-1190 degrees
3Bolts 1-1190 degrees
4Bolt 1111 ft. lbs
Cylinder Head — tightening sequence 5 stages
1Bolts 1-1130 ft. lbs
2Turn 90 degrees90 degrees
3Turn 90 degrees90 degrees
4Turn 90 degrees90 degrees
511
Engine Flywheel Bolts — tightening sequence 1 stages
115.0 ft. lbs., Step 2: 33.0 ft. lbs., Step 3: 9015 ft. lbs
Exhaust Manifold to Cylinder Head Bolts — tightening sequence 3 stages
110.3 ft. lbs.10.3 ft. lbs
210.3 ft. lbs.10.3 ft. lbs
310.3

Common OBD-II trouble codes

The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.

P0420
Catalyst system efficiency below threshold — Bank 1
P0300
Random / multiple cylinder misfire detected
P0171
System too lean — Bank 1
P0455
Evaporative emission system leak detected — large leak
P0128
Coolant thermostat below regulating temperature
P0442
Evaporative emission system leak detected — small leak

VIN tools

Decode factory build data for a specific vehicle by VIN.

VIN
Decode a VIN to confirm the transmission and build data for a specific GLC63 AMG S. OEM
Build data
Plant, GVWR class, engine and body data for any 17-character VIN.
Recalls
Check open recall campaigns against a specific vehicle by VIN.

Vehicles with shared specs

Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.

Reference guides

Cross-vehicle references for the kinds of data on this page.