MercedesGLA45 AMG2017Overview/mercedes/gla45-amg/2017/base/

2017 Mercedes GLA45 AMG

Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2017 GLA45 AMG.

Model year2022201920182017

Quick specs

Fluid capacities, tune-up values and fuel economy at a glance.

Lug nut torque96 ft-lbsOEM · verified

Fitment & sizes

Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.

From the factory this vehicle uses a BCI 48 · 760 CCA battery, OE oil filter 2701840280. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.

Battery groupBCI 48 · 760 CCAOEM · verified
Tire sizeP235/45R19OEM · verified
Wheel / rim8.0 inOEM · verified

OE service part numbers OEM · verified

Engine oil filter2701840280 alt 278180000990
Battery0019828008 alt 000982960864
Front wiper blades1768204300
Thermostat024997634564 alt 2702002200

Service quick specs OEM factory data

Capacities, torques and tune-up values from the factory service manual.

Torque lug nuts to 96 ft-lbs. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.

Engine torques

Intake Manifold to Engine Bolts6.6
Exhaust Manifold to Cylinder Head Bolts15.5
Oil Pump to Cylinder BLock Bolts/Studs10.0 ft-lbs

Chassis torques

Lug Nuts96 ft-lbs

Battery & A/C

Standard BCI Group Number48
Standard BCI Cranking Performance760 cca
Optional BCI Group NumberAUXILIARY: 400
Optional BCI Cranking PerformanceAUXILIARY: 200 cca

Multi-step torque procedures OEM · verified

Camshaft Bearing/Carrier Cap Bolts or Studs — tightening sequence 1 stages
17.4 ft. lbs., Step 2: 907.4 ft. lbs
Connecting Rod (Large End) Bearings — tightening sequence 1 stages
144.0 inch lbs., Step 2: 132.0 inch lbs., Step 3: 9044 in
Crankshaft Pulley and/or Damper Bolts — tightening sequence 2 stages
1148.0 ft. lbs.148 ft. lbs
2+ 90
Cylinder Head — tightening sequence 6 stages

Prep Do not reuse old bolts. Use new bolts coated with clean engine oil. Tighten all bolts to finger tight then continue on with the following procedure.

1Bolts 1-1014.7 ft. lbs
229.5 ft. lbs.29.5 ft. lbs
390 degrees90 degrees
490 degrees90 degrees
590 degrees90 degrees
614.8
Engine Flywheel Bolts — tightening sequence 1 stages
133.0 ft. lbs., Step 2: 9033 ft. lbs
Main Bearings — tightening sequence 1 stages
122.0 ft. lbs., Step 2: 9022 ft. lbs

Common OBD-II trouble codes

The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.

P0420
Catalyst system efficiency below threshold — Bank 1
P0300
Random / multiple cylinder misfire detected
P0171
System too lean — Bank 1
P0455
Evaporative emission system leak detected — large leak
P0128
Coolant thermostat below regulating temperature
P0442
Evaporative emission system leak detected — small leak

VIN tools

Decode factory build data for a specific vehicle by VIN.

VIN
Decode a VIN to confirm the transmission and build data for a specific GLA45 AMG. OEM
Build data
Plant, GVWR class, engine and body data for any 17-character VIN.
Recalls
Check open recall campaigns against a specific vehicle by VIN.

Vehicles with shared specs

Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.

Reference guides

Cross-vehicle references for the kinds of data on this page.