Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2015 GL350.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 49 · 850 CCA battery, OE oil filter 013997614564. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 013997614564 alt 0299975448 |
| Battery | 0019828208 |
| Front wiper blades | 166820104528 |
| Thermostat | 6422002315 |
| Cabin air filter | 1668300218 |
Engine, drivetrain, dimensions and economy.
| Overall length | 202 in |
| Overall width | 76 in |
| Overall height | 72.4 in |
| Wheelbase | 121.3 in |
| Curb weight | 5370 lb |
| Track (front / rear) | 66.1 / 66.9 in |
| Weight distribution (front / rear) | 50/50 |
Capacities, torques and tune-up values from the factory service manual.
This engine DOT 4 brake fluid. Torque the oil drain plug to 22.1 ft-lbs. The firing order is 1-4-2-5-3-6. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Brake Fluid | DOT 4 |
| Engine Coolant Capacity | 12.2 |
| Fuel Tank Capacity | 26.4 gallons |
| Intake Manifold to Engine Bolts | 13.3 ft/lbs. |
| Exhaust Manifold to Cylinder Head Bolts | 18.4 |
| Intake Manifold to Engine Bolts | 12.5 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 18.4 ft-lbs |
| Engine Oil Pan Drain Plug | 22.1 ft-lbs |
| Cylinder Firing Order | 1-4-2-5-3-6 |
| Cylinder Firing Order | 1-4-2-5-3-6 |
| Refrigerant Capacity | 2.31-2.37 lbs |
| Oil Type | 46 |
| Oil Capacity | 4.06-5.41 oz |
| Refrigerant | R134a |
| Oil Group | PAG |
| Standard BCI Group Number | 49 |
| Standard BCI Cranking Performance | 850 cca |
| Engine Compression | Diesel psi 333-435 / max variation 43 psi |
| Minimum Pad Thickness | Front: 0.079; Rear: 0.079 Vehicle |
| Vented Rotor Minimum Thickness for Replacement | Rear: .764 |
| Vented Rotor Minimum Thickness after Refinish | Rear: .787 |
| 1 | 184.0 ft. lbs., Step 2: Back off 180 degrees, Step 3: 147.0 ft. lbs., Step 4: 30 | 184 ft. lbs |
| 1 | 258.0 ft. lbs., Step 2: Back off 180 degrees, Step 3: 184.0 ft. lbs., Step 4: 30 | 258 ft. lbs |
Prep Do not reuse old bolts. Coat new bolts lightly with specified motor oil. The length of new M12 cylinder head bolts are 205mm. if the length of the M12 bolts are greater than the maximum permissible dimension of 207mm, replace with new cylinder head bolts. · Bolts 1-8
| 1 | 7.4 ft. lbs.; Bolt 11 | 7.4 ft. lbs |
| 1 | 14.8 ft. lbs.; Bolts 1-8 | 14.8 ft. lbs |
| 2 | 44.25 ft. lbs.; Bolt 11 | 44.25 ft. lbs |
| 2 | 14.8 ft. lbs.; Bolts 1-8 | 14.8 ft. lbs |
| 3 | 90 degrees; Bolt 11 | 90 degrees |
| 3 | 14.8 ft. lbs.; Bolts 1-8 | 14.8 ft. lbs |
| 4 | 90 degrees; Bolt 11 | 90 degrees |
| 4 | 14.8 ft. lbs.; Bolts 1-8 | 14.8 ft. lbs |
| 5 | 90 degrees; Bolt 11 | 90 degrees |
| 5 | 14.8 ft. lbs. | 14.8 ft. lbs |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.