Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2018 E63 AMG S.
Fluid capacities, tune-up values and fuel economy at a glance.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses OE oil filter 0309970748. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 0309970748 alt 278180000990 |
| Spark plug | 0001590500 |
| Battery | 0019828208 |
| Front wiper blades | 2138203604 |
| Thermostat | 1772007901 |
| Cabin air filter | 1668300218 |
Engine, drivetrain, dimensions and economy.
| Overall length | 196.9 in |
| Overall width | 72.8 in |
| Overall height | 58.3 in |
| Wheelbase | 115.7 in |
| Curb weight | 4669 lb |
| Track (front / rear) | 63 / 63.4 in |
| Weight distribution (front / rear) | 54/46 |
Capacities, torques and tune-up values from the factory service manual.
Torque lug nuts to 96 ft-lbs. The firing order is 1-5-4-2-6-3-7-8. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Oxygen (O2S) Sensor Bolt(s) | 30.0 ft-lbs |
| Knock Sense (KS) Bolt(s) | 16.0 ft-lbs |
| Intake Manifold to Engine Bolts | 9.6 ft-lbs |
| Oil Pump to Cylinder BLock Bolts/Studs | 18.0 ft-lbs |
| Lug Nuts | 96 ft-lbs |
| Cylinder Firing Order | 1-5-4-2-6-3-7-8 |
| Spark Plug Manufacturer | Mercedes-Benz |
| Spark Plug Gap | .031 in |
| Spark Plug Torque | 16 ft-lbs |
| Engine Compression | 189 |
| Brake Caliper Bolt to Carrier Torque | Front: 26; Rear: 18 |
| Brake Caliper Carrier to Hub Bolt Torque | Rear: 44 ft-lbs |
| Vented Rotor Minimum Thickness for Replacement | Front: 1.299; Rear: .944 |
| 1 | 44.0 inch lbs., Step 2: 22.0 ft. lbs., Step 3: 90 | 44 in |
| 1 | 148.0 ft. lbs., Step 2: 90 | 148 ft. lbs |
Prep Do not reuse old bolts. Use new bolts coated with clean engine oil. Tighten all bolts to finger tight then continue on with the following procedure.
| 1 | Bolts 1-11 | 30 ft. lbs |
| 2 | Bolts 1-11 | 90 degrees |
| 3 | Bolts 1-11 | 90 degrees |
| 4 | Bolt 11 | 11 ft. lbs |
| 1 | 15.0 ft. lbs., Step 2: 33.0 ft. lbs., Step 3: 90 | 15 ft. lbs |
| 1 | 10.3 ft. lbs. | 10.3 ft. lbs |
| 2 | 10.3 ft. lbs. | 10.3 ft. lbs |
| 3 | 10.3 | |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.