Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2003 E320 Wagon 4matic.
The 2003 Mercedes E320 Wagon 4matic takes 8.5 qt of 0W-30 engine oil.
Fluid capacities, tune-up values and fuel economy at a glance.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 49 · 825 CCA battery, OE oil filter 0169971745. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 0169971745 alt 0259976548 |
| Engine air filter | 1120940104 |
| Battery | 0019828208 alt 0019828008 |
| Front wiper blades | 2108200245 alt 2118202945 |
| Thermostat | 1122030076 alt 1122030275 |
| Cabin air filter | 2118301218 alt 2118301200 |
Engine, drivetrain, dimensions and economy.
| Overall length | 190.2 in |
| Overall width | 71.3 in |
| Overall height | 57.1 in |
| Wheelbase | 112.2 in |
| Curb weight | 3638 lb |
| Track (front / rear) | 61.8 / 61 in |
| Weight distribution (front / rear) | 50/50 |
Capacities, torques and tune-up values from the factory service manual.
This engine holds 8.5 qt of 0W-30 / 5W-30 / 0W-40 engine oil, DOT 4 brake fluid. Torque lug nuts to 96 ft-lbs, the oil drain plug to 22.0 ft-lbs. The firing order is 1-4-3-6-2-5. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Brake Fluid | DOT 4 |
| Differential Gear Oil Capacity | 2.1 Pints |
| Differential Gear Oil Capacity | 2.7 Pints |
| Engine Coolant | USE ONLY COOLANT MEETING MB SHEET 325.0 |
| Engine Oil | 0W-30 · 5W-30 · 0W-40 · 5W-40 · 5W-50 |
| Engine Oil Capacity | 8.5 qt |
| Intake Manifold to Engine Bolts | 15 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 12 ft-lbs |
| Engine Oil Pan Drain Plug | 22.0 ft-lbs |
| Lug Nuts | 96 ft-lbs |
| Cylinder Firing Order | 1-4-6-3-2-5 |
| Cylinder Firing Order | 1-5-3-6-2-4 |
| Cylinder Firing Order | 1-4-3-6-2-5 |
| Curb Idle Speed (No Load) | 725 rpm |
| Curb Idle Speed Variance (No Load) | 75 rpm |
| Spark Plug Gap | 0.031 in |
| Ignition Timing | 6-10 degrees |
| Refrigerant | R134a |
| Refrigerant Capacity | 2.20 lbs |
| Oil Group | PAG |
| Oil Type | MB part number 0019890803 or equivalent |
| Oil Capacity | 5.20 oz |
| Standard BCI Group Number | 49 |
| Standard BCI Cranking Performance | 825 cca |
| Pressure Test | 20 psi |
| Thermostat Opening Temperature | 185-192 °F |
| Regulated Fuel System Pressure (Without Vacuum) | 54.0-61.0 psi |
| Regulated Fuel System Pressure (With Vacuum) | 46.0-52.0 psi |
| Injector Primary Resistance | 14-18 ohms |
| Engine Oil Pressure | 10 psi @ 700 rpm, 43.5 @ 3000 rpm psi |
| Intake Valve Lash | Hydraulic in |
| Exhaust Valve Lash | Hydraulic in |
| Minimum Pad Thickness | Front: 0.079; Rear: 0.079 in |
| Rotor Nominal Thickness From | 1.102 in / 0.472 in |
| Rotor Nominal Thickness To | 1.102 in / 0.472 in |
| Rotor Minimum Machining | 1.024 in / 0.413 in |
| Rotor Discard at or Under | 1 in / 0.386 in |
| 1 | 7 ft. lbs. | 7 ft. lbs |
| 2 | 22 ft. lbs. | 22 ft. lbs |
| 3 | 90 degrees | 90 degrees |
| 4 | 90 | |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.
8.5 qt of 0W-30, 5W-30, 0W-40, 5W-40 OR 5W-50, per the factory manual.