Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2014 CL65 AMG.
The 2014 Mercedes CL65 AMG takes 9.5 qt of 0W-30 engine oil.
Fluid capacities, tune-up values and fuel economy at a glance.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI 49 · 850 CCA battery, OE oil filter 2751800009. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 2751800009 |
| Engine air filter | 2750940204 |
| Battery | 0019828208 |
| Front wiper blades | 2218201300 |
| Thermostat | 1372030180 |
| Cabin air filter | 2218300718 |
Capacities, torques and tune-up values from the factory service manual.
This engine holds 9.5 qt of 0W-30 / 5W-30 / 0W-40 engine oil, DOT 4 brake fluid. Torque lug nuts to 110 ft-lbs, the oil drain plug to 22.1 ft-lbs. The firing order is 1-12-5-8-3-10-6-7-2-11-4-9. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Automatic Transmission Fluid | ATF |
| Automatic Transmission Fluid Capacity | 8.5-10.5 |
| Brake Fluid | DOT 4 |
| Differential Gear Oil Capacity | 3 Pints |
| Engine Oil | 0W-30 · 5W-30 · 0W-40 · 5W-40 · 5W-50 |
| Engine Oil Capacity | 9.5 qt |
| Intake Manifold to Engine Bolts | 6 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 11 ft-lbs |
| Intake Manifold to Engine Bolts | 6.0 ft-lbs |
| Exhaust Manifold to Cylinder Head Bolts | 11.0 ft-lbs |
| Engine Oil Pan Drain Plug | 22.1 ft-lbs |
| Lug Nuts | 110 ft-lbs |
| Cylinder Firing Order | 1-12-5-8-3-10-8-7-2-11-4-9 |
| Cylinder Firing Order | 1-12-5-8-3-10-6-7-2-11-4-9 |
| Refrigerant | R134a |
| Refrigerant Capacity | 2.40 lbs |
| Oil Group | PAG |
| Oil Type | 46 |
| Oil Capacity | 3.72 oz |
| Standard BCI Group Number | 49 |
| Standard BCI Cranking Performance | 850 cca |
| Optional BCI Group Number | V4 |
| Engine Compression | 174 |
| Engine Compression | 174-203 psi |
| Torque Caliper to Bracket | 81 ft-lbs / 21 ft-lbs |
| Torque to Knuckle | 110 ft-lbs / 133 ft-lbs |
| Rotor Nominal Thickness From | 1.023 in / 1.417 in |
| Rotor Nominal Thickness To | 1.023 in / 1.417 in |
| Rotor Minimum Machining | 0.944 in / 1.338 in |
| Rotor Discard at or Under | 0.921 in / 1.315 in |
| 1 | 202 ft. lbs., step 2: 90 | 202 ft. lbs |
| 1 | 30 ft. lbs. | 30 ft. lbs |
| 2 | 90 degrees | 90 degrees |
| 3 | 90 degrees; The length of the new M10 cylinder head bolts are 168.5 mm. If the length of the M10 bolts are greater than the maximum permissible dimension (170 mm), replace with new cylinder head bolts. | 90 degrees |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.
9.5 qt of 0W-30, 5W-30, 0W-40, 5W-40 OR 5W-50, per the factory manual.