Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2016 C63 AMG S.
Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.
From the factory this vehicle uses a BCI Battery group and CCA will vary by model options and region. Refer to the appropriate service information. · Battery group and CCA will vary by model options and region. Refer to the appropriate service information. CCA battery, OE oil filter 0309970748. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.
| Engine oil filter | 0309970748 alt 278180000990 |
| Engine air filter | 177094000464 |
| Spark plug | 0001590500 |
| Battery | 0019828208 alt 0009826925 |
| Front wiper blades | 2058204503 |
| Thermostat | 1772008801 |
| Cabin air filter | 1668300218 |
Engine, drivetrain, dimensions and economy.
| Overall length | 185.4 in |
| Overall width | 69.7 in |
| Overall height | 55.5 in |
| Wheelbase | 108.7 in |
| Curb weight | 3814 lb |
| Track (front / rear) | 59.4 / 59.4 in |
| Weight distribution (front / rear) | 53/47 |
Capacities, torques and tune-up values from the factory service manual.
This engine 75W-85 · 75W-83 in the differential, DOT 4 brake fluid. The firing order is 1-5-4-2-6-3-7-8. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.
| Brake Fluid | DOT 4 |
| Differential Gear Oil | 75W-85 · 75W-83 |
| Differential Gear Oil Capacity | 2.0-4.0 |
| Intake Manifold to Engine Bolts | 9.6 ft-lbs |
| Cylinder Firing Order | 1-5-4-2-6-3-7-8 |
| Cylinder Firing Order | 1-5-4-2-6-3-7-8 |
| Spark Plug Manufacturer | Mercedes-Benz |
| Spark Plug Gap | 0.031 in |
| Spark Plug Torque | 15.0-20.0 ft-lbs |
| Refrigerant | R134a |
| Refrigerant Capacity | 1.30-1.41 lbs |
| Oil Group | PAG |
| Oil Type | 46 |
| Brake Caliper Bolt to Carrier Torque | Front: 30; Rear: 85 /; Rear: 26 |
| Brake Caliper Carrier to Hub Bolt Torque | Front: 33; Rear: 85 /; Rear: 44 Turn |
| ABS Sensor Torque | 6.6 / NS |
| Minimum Pad Thickness | Front: 0.079; Rear: 0.079 Vehicle |
| Vented Rotor Minimum Thickness for Replacement | Rear: .945 |
Prep Do not reuse old bolts. Coat new bolts lightly with specified motor oil. · Bolts 1-11
| 1 | 30.0 ft. lbs. | 30 ft. lbs |
| 2 | 90 degrees | 90 degrees |
| 3 | 90 degrees | 90 degrees |
| 4 | 90 degrees | 90 degrees |
| 5 | Bolt 11 11.0 ft. lbs. | 11 ft. lbs |
| 1 | 10.3, Step 3: 10.3 | |
The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.
Decode factory build data for a specific vehicle by VIN.
Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.
Cross-vehicle references for the kinds of data on this page.