JaguarXKR 1002002Overview/jaguar/xkr-100/2002/base/

2002 Jaguar XKR 100

Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2002 XKR 100.

Quick specs

Fluid capacities, tune-up values and fuel economy at a glance.

Lug nut torque95 ft-lbsOEM · verified

Fitment & sizes

Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.

From the factory this vehicle uses a BCI 49 · 680 CCA battery, OE oil filter EAZ1354. Note the factory cabin air filter is now discontinued — plan on a superseded or quality aftermarket equivalent, which the part pages below list where known. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.

Battery groupBCI 49 · 680 CCAOEM · verified
Tire size245-50ZR17OEM · verified
Wheel / rim8-J inOEM · verified

OE service part numbers OEM · verified

Engine oil filterEAZ1354
Engine air filterNJA3558AA
Fuel filterC2C35417 alt HJA3099AA
Spark plugNCA3850HA2
BatteryC2D61169
Front wiper bladesGJA8960BB alt GJA8962CB
ThermostatNCA2246BA alt AJ86484
Cabin air filterMJD6863AA discontinued

Full specifications

Engine, drivetrain, dimensions and economy.

Dimensions & weight NHTSA vPIC

Overall length187.4 in
Overall width72 in
Overall height50.8 in
Wheelbase102 in
Curb weight4021 lb
Track (front / rear)59.1 / 59.1 in

Service quick specs OEM factory data

Capacities, torques and tune-up values from the factory service manual.

This engine DOT 4 brake fluid. Torque lug nuts to 95 ft-lbs. The firing order is 1-5-4-2-6-3-7-8. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.

Lubricants & capacities

Brake FluidDOT 4
Power Steering FluidATF

Engine torques

Camshaft Bearing/Carrier Cap Bolts or Studs8.0 ft-lbs
Intake Manifold to Engine Bolts15-16 ft-lbs
Exhaust Manifold to Cylinder Head Bolts13 ft-lbs
Oil Pump to Cylinder BLock Bolts/Studs9 ft-lbs

Chassis torques

Lug Nuts95 ft-lbs

Ignition

Cylinder Firing Order1-5-4-2-6-3-7-8
Spark Plug Gap0.035-0.039 in
Spark Plug Torque11.0 ft-lbs

Battery & A/C

RefrigerantR134a
Refrigerant Capacity1.32-1.54 lbs
Oil TypePAG
Oil Capacity5.41-6.76 oz
Standard BCI Group Number49
Standard BCI Cranking Performance680 cca

Service checks

Injector Primary Resistance12-18 ohms
Intake Valve Lash0.0008 in
Exhaust Valve Lash0.0014 in

Brakes

Brake ApplicationWITH BREMBO BRAKES / WITH STANDARD BRAKES
Torque Caliper to Bracket180 ft-lbs / 18-22 ft-lbs
Torque to Knuckle75 ft-lbs / 60 ft-lbs / 103 ft-lbs
Minimum Pad Thickness0.078 in
Brake ApplicationWITH BREMBO BRAKES / WITH STANDARD BRAKES
Rotor Runout Limit0.003 in / 0.005 in
Rotor Nominal Thickness From1.26 in / 1.102 in / 1.122 in / 0.787 in
Rotor Nominal Thickness To1.26 in / 1.102 in / 1.122 in / 0.787 in

Multi-step torque procedures OEM · verified

Cylinder Head — tightening sequence 4 stages

Prep Coat bolts with engine oil. Do not reuse bolts more than twice. Tighten all bolts to finger tight then continue on with the following procedure. · M8 Bolts

117.0-20.0 ft. lbs.; M10 Bolts17–20 ft. lbs
115.0 ft. lbs.15 ft. lbs
225.9 ft. lbs.25.9 ft. lbs
390 degrees90 degrees
490 degrees90 degrees

Factory maintenance schedule OEM · verified

Normal service, condensed from the factory interval matrix.

Under the factory schedule, replace the engine oil and filter every 10,000 mi; spark plugs every 60,000 mi; coolant every 10,000 mi. The big-interval services (every 10,000 mi for coolant, and the transmission fluid) are the ones owners most often skip — on a lower-mileage example, assume the original fluids are still in it and check them first.

Every 10,000 miEngine Coolant System (leak inspection) · Engine Oil (drain & refill) · Engine Oil Filter (replace) · Windshield Wiper Blade (replace)
Every 20,000 miCabin Air Filter (replace) · Engine Air Filter Element (replace)
Every 30,000 miBrake Hydraulic System (drain, refill & bleed)
Every 60,000 miFuel Filter (replace) · Spark Plugs (replace)
Every 100,000 miDrive Belt (replace)

Common OBD-II trouble codes

The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.

P0420
Catalyst system efficiency below threshold — Bank 1
P0300
Random / multiple cylinder misfire detected
P0171
System too lean — Bank 1
P0455
Evaporative emission system leak detected — large leak
P0128
Coolant thermostat below regulating temperature
P0442
Evaporative emission system leak detected — small leak

VIN tools

Decode factory build data for a specific vehicle by VIN.

VIN
Decode a VIN to confirm the transmission and build data for a specific XKR 100. OEM
Build data
Plant, GVWR class, engine and body data for any 17-character VIN.
Recalls
Check open recall campaigns against a specific vehicle by VIN.

Vehicles with shared specs

Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.

Reference guides

Cross-vehicle references for the kinds of data on this page.