FordPolice Interceptor Utility2019Overview/ford/police-interceptor-utility/2019/base/

2019 Ford Police Interceptor Utility

Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2019 Police Interceptor Utility.

The 2019 Ford Police Interceptor Utility takes 6.0 qt of 5W-30 engine oil.

Quick specs

Fluid capacities, tune-up values and fuel economy at a glance.

Engine oil capacity6.0 qtOEM · verified
Engine oil type5W-30 / 0W-30 / 5W-20OEM · verified

Fitment & sizes

Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.

From the factory this vehicle uses a BCI 65 · 750 CCA battery. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.

Battery groupBCI 65 · 750 CCAOEM · verified
Tail / brake / turnBATTERYOEM · verified

Full specifications

Engine, drivetrain, dimensions and economy.

Dimensions & weight NHTSA vPIC

Overall length197.2 in
Overall width78.7 in
Overall height70.5 in
Wheelbase112.6 in
Curb weight4791 lb
Track (front / rear)66.9 / 66.9 in

Service quick specs OEM factory data

Capacities, torques and tune-up values from the factory service manual.

This engine holds 6.0 qt of 5W-30 / 0W-30 / 5W-20 engine oil, Dot 4 brake fluid. The firing order is 1-4-2-5-3-6.

Lubricants & capacities

Brake FluidDot 4
Engine Coolant Capacity13.4
Engine Oil5W-30 · 0W-30 · 5W-20 · 0W-20
Engine Oil Capacity6.0 qt

Engine torques

Engine Flywheel Bolts59 ft-lbs
Oil Pump to Cylinder BLock Bolts/Studs89 inch lbs. ft-lbs

Chassis torques

Front Wheel Hub258.0
Rear Wheel Hub258.0

Ignition

Cylinder Firing Order1-4-2-5-3-6
Cylinder Firing Order1-4-2-5-3-6

Battery & A/C

RefrigerantR1234yf
Oil GroupPAG
Standard BCI Group Number65
Standard BCI Cranking Performance750 cca

Service checks

Key ON Engine OFF (KOEO)55.0

Brakes

Brake Caliper Bolt to Carrier TorqueFront: 13; Rear: 24.0 ft-lbs
Brake Caliper Carrier to Hub Bolt TorqueFront: 122.0 ft-lbs; Rear: 76 ft-lbs
ABS Sensor TorqueFront: 6.0; Rear: 6.0
Vented Rotor Minimum Thickness for ReplacementFront: 1.122; Rear: .394
Maximum Rotor Runout.002

Multi-step torque procedures OEM · verified

Camshaft Bearing/Carrier Cap Bolts or Studs — tightening sequence 1 stages
171 inch lbs., Step 2: 45°.71 in
Connecting Rod (Large End) Bearings — tightening sequence 1 stages
117 ft. lbs., Step 2: 32 ft. lbs., Step 3: 90°.17 ft. lbs
Cylinder Head — tightening sequence 1 stages
1Bolts 1-814.8 ft. lbs
Cylinder Head — tightening sequence 1 stages
1Bolts 1-814.8 ft. lbs
Intake Manifold to Engine Bolts — tightening sequence 1 stages
17.4 ft. lbs., Step 2: Turn 45°7.4 ft. lbs

Factory maintenance schedule OEM · verified

Normal service, condensed from the factory interval matrix.

Under the factory schedule, replace the spark plugs every 100,000 mi; coolant every 50,000 mi. The big-interval services (every 50,000 mi for coolant, and the transmission fluid) are the ones owners most often skip — on a lower-mileage example, assume the original fluids are still in it and check them first.

Every 10,000 miBrake Line (inspect) · Brake Linings (inspect) · Brake Rotor (inspect) · CV Joint Boot (inspect) · Drive Axle Assembly (inspect) · Driveshaft (inspect)
Every 20,000 miAccessory Drive Belt (inspect) · Cabin Air Filter (replace)
Every 30,000 miEngine Air Filter Element (replace) · Transmission Assembly (drain & refill)
Every 50,000 miEngine Coolant System (drain, flush & refill)
At 100,000 miAccessory Drive Belt (inspect) · Engine Coolant System (drain, flush & refill)
Every 100,000 miSpark Plugs (replace)
At 150,000 miDrive Belt (replace)

Common OBD-II trouble codes

The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.

P0420
Catalyst system efficiency below threshold — Bank 1
P0300
Random / multiple cylinder misfire detected
P0171
System too lean — Bank 1
P0455
Evaporative emission system leak detected — large leak
P0128
Coolant thermostat below regulating temperature
P0442
Evaporative emission system leak detected — small leak

VIN tools

Decode factory build data for a specific vehicle by VIN.

VIN
Decode a VIN to confirm the transmission and build data for a specific Police Interceptor Utility. OEM
Build data
Plant, GVWR class, engine and body data for any 17-character VIN.
Recalls
Check open recall campaigns against a specific vehicle by VIN.

Vehicles with shared specs

Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.

Reference guides

Cross-vehicle references for the kinds of data on this page.

Frequently asked

How much oil does the 2019 Police Interceptor Utility take?

6.0 qt of Engines Equipped with Turbo: Above -20°F use 5W-30, below -22°F use 0W-30; Non Turbo Engines: Temperatures above -20°F use 5W-20, Temperatures below -22°F use 0W-20., per the factory manual.