Ford›F-Series B-Series›1999›Overview/ford/f-series-b-series/1999/base/

1999 Ford F-Series B-Series

Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 1999 F-Series B-Series.

The 1999 Ford F-Series B-Series takes 6.0 qt of 5W-20 engine oil.

Model year19991992

Quick specs

Fluid capacities, tune-up values and fuel economy at a glance.

Engine oil capacity6.0 qtOEM · verified
Engine oil type5W-20 APIOEM · verified
Lug nut torque150-165 ft-lbsOEM · verified

Fitment & sizes

Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.

From the factory this vehicle uses a BCI 59 - UNDER 8500 LBS. · 540 - UNDER 8500 LBS. CCA battery. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.

Battery groupBCI 59 - UNDER 8500 LBS. · 540 - UNDER 8500 LBS. CCAOEM · verified
Tire sizeP235-70R16SLOEM · verified
Wheel / rim7-J inOEM · verified

Performance & power Independent road tests

0–60 mph, quarter-mile, horsepower and torque from independent road tests.

Independent road tests for the F-Series B-Series of this era, listed by trim and engine — this page spans more than one engine, so no single horsepower figure is shown.

6.0–10.4 sec0–60 mph (tested)quickest 5.96 sec — 2003 F-150 Harley-Davidson SuperCrew (5.4 ft. Bed)
YearTrim / engine0–60¼ mileHPDrivetrain
1998F-150 XLT SuperCab 5.4L V88.70 sec16.70 sec235 hpRWD
1998F-150 XLT SuperCab 5.4L V89.40 sec17.20 sec235 hp4x4
2000F-150 XLT SuperCab (6.6 ft. Bed) 5.4L V88.90 sec16.70 sec260 hp4x4
1997F-150 Lariat SuperCab 5.4L V88.30 sec16.40 sec235 hpRWD
1997F-150 XLT Regular Cab 4.6L V88.80 sec16.60 sec220 hpRWD
1997F-150 Lariat Flareside Regular Cab 4.6L V88.90 sec16.70 sec220 hpRWD
1997F-150 Styleside Regular Cab 4.2L V69.30 sec17.20 sec202 hpRWD
1997F-150 XLT SuperCab 4.6L V89.90 sec17.70 sec220 hpRWD

Service quick specs OEM factory data

Capacities, torques and tune-up values from the factory service manual.

This engine holds 6.0 qt of 5W-20 API engine oil, SYNTHETIC · 75W-140 · GL-5 in the differential, DOT 3 brake fluid. Torque lug nuts to 150-165 ft-lbs. The firing order is 1-3-7-2-6-5-4-8. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.

Lubricants & capacities

Brake FluidDOT 3
Differential Gear OilSYNTHETIC · 75W-140 · GL-5
Differential Gear Oil Capacity5.5 Pints Rear, 8.8 and 9.7
Engine Oil5W-20 · API
Engine Oil Capacity6.0 qt
Engine Oil5W-20 · API
Engine Oil Capacity6.0 qt
Engine Oil5W-20 · API

Engine torques

Camshaft Bearing/Carrier Cap Bolts or Studs6-9 ft-lbs
Crankshaft Pulley and/or Damper Bolts118 ft-lbs
Engine Flywheel Bolts54-64 ft-lbs
Engine Flywheel Bolts59 ft-lbs
Engine Flywheel Bolts55-64 ft-lbs
Engine Flywheel Bolts54-64 ft-lbs
Intake Manifold to Engine Bolts15-22 ft-lbs
Exhaust Manifold to Cylinder Head Bolts17-20 ft-lbs

Chassis torques

Leaf Spring to Axle (U-bolts)73.0-97.0 ft-lbs
Leaf Spring to Chassis Bracket157.0-212-0 ft-lbs
Leaf Spring to Rear Shackle73.0-97.0 ft-lbs
Leaf Spring Rear Shackle to Chassis Bracket73.0-97.0 ft-lbs
Lug Nuts150-165 ft-lbs
Transfer Case Fill Plug11.0 ft-lbs
Transfer Case Drain Plug11.0 ft-lbs
Front Wheel Hub221 ft-lbs

Ignition

Cylinder Firing Order1-4-2-5-3-6
Cylinder Firing Order1-3-7-2-6-5-4-8
Curb Idle Speed (No Load)755 rpm
Curb Idle Speed Variance (No Load)75 rpm
Curb Idle Speed (No Load)760 DOHC rpm
Spark Plug ManufacturerMotorcraft
Spark Plug Gap0.052-0.056 in
Spark Plug Torque11.0 ft-lbs

Battery & A/C

RefrigerantR134a
Oil GroupPAG
Standard BCI Group Number59 - UNDER 8500 LBS.
Standard BCI Cranking Performance540 - UNDER 8500 LBS. cca
Optional BCI Group Number65 - OVER 8500 LBS.
Optional BCI Cranking Performance650 - OVER 8500 LBS. cca
Standard BCI Group Number65 - OVER 8500 LBS
Standard BCI Cranking Performance650 - OVER 8500 LBS cca

Service checks

Key ON Engine OFF (KOEO)30-45
Key ON Engine OFF (KOEO)30-45
Key ON Engine OFF (KOEO)80-120 CNG
Injector Primary Resistance11-18 na ohms
Injector Primary Resistance11-18 na ohms
Injector Primary Resistance11-18 na ohms
Engine Oil Pressure40-125 psi
Engine Oil Pressure RPM2500 rpm

Brakes

Brake ApplicationWITH REAR DISC
Torque Caliper to Bracket20 ft-lbs
Torque to Knuckle70 ft-lbs
Brake ApplicationWITH STANDARD
Torque Caliper to Bracket21-26 ft-lbs
Torque to Knuckle136 ft-lbs
Brake ApplicationWITH STANDARD
Torque Caliper to Bracket21-26 ft-lbs

Multi-step torque procedures OEM · verified

Connecting Rod (Large End) Bearings — tightening sequence 1 stages
129 ft. lbs., Step 2: 9029 ft. lbs
Connecting Rod (Large End) Bearings — tightening sequence 1 stages
133 ft. lbs., Step 2: 90 degrees, Step 3: 12033 ft. lbs
Connecting Rod (Large End) Bearings — tightening sequence 1 stages
133 ft. lbs., Step 2: 90 degrees, Step 3: 12033 ft. lbs
Connecting Rod (Large End) Bearings — tightening sequence 1 stages
118 ft. lbs., Step 2: 30 ft. lbs., Step 3: 9018 ft. lbs
Crankshaft Pulley and/or Damper Bolts — tightening sequence 1 stages
166 ft. lbs., Step 2: loosen one turn, step 3: 37 ft. lbs., step 4: 9066 ft. lbs
Crankshaft Pulley and/or Damper Bolts — tightening sequence 1 stages
166 ft. lbs., step 2: Loosen one turn., step 3: 37 ft. lbs., step 4: 9066 ft. lbs
Cylinder Head — tightening sequence 3 stages
130 ft. lbs.30 ft. lbs
290 degrees90 degrees
390
Cylinder Head — tightening sequence 3 stages
1all bolts15 ft. lbs
2all bolts30 ft. lbs
3all bolts37 ft. lbs
1loosen 2-3 turn
2if long bolt33 ft. lbs
3180 degrees; Proceed to next bolt in sequence180 degrees
Cylinder Head — tightening sequence 3 stages
130 ft. lbs.30 ft. lbs
290 degrees90 degrees
390
Cylinder Head — tightening sequence 3 stages
130 ft. lbs.30 ft. lbs
290 degrees90 degrees
390
Cylinder Head — tightening sequence 3 stages
130 ft. lbs.30 ft. lbs
290 degrees90 degrees
390
Cylinder Head — tightening sequence 3 stages
130 ft. lbs.30 ft. lbs
290 degrees90 degrees
390
Cylinder Head — tightening sequence 3 stages
130 ft. lbs.30 ft. lbs
290 degrees90 degrees
390
Intake Manifold to Engine Bolts — tightening sequence 1 stages
14 ft. lbs., step 2: 6-84 ft. lbs
Main Bearings — tightening sequence 1 stages
137 ft. lbs., Step 2: 115-12537 ft. lbs

Factory maintenance schedule OEM · verified

Normal service, condensed from the factory interval matrix.

Under the factory schedule, replace the engine oil and filter every 5,000 mi; spark plugs every 100,000 mi; coolant every 30,000 mi. The big-interval services (every 30,000 mi for coolant, and the transmission fluid) are the ones owners most often skip — on a lower-mileage example, assume the original fluids are still in it and check them first.

Every 3,000 miDrive Axle Assembly (drain & refill)
Every 5,000 miEngine Oil (drain & refill) · Engine Oil Filter (replace) · Tire & Wheel Assembly (rotate)
Every 15,000 miBrake System (inspect) · Cabin Air Filter (replace) · Engine Coolant System (leak inspection) · Steering Linkage (inspect) · Suspension Ball Joint (inspect) · Suspension System (inspect)
Every 30,000 miDriveshaft Slip Yoke (lubricate) · Engine Air Filter Element (replace) · Engine Coolant System (drain, flush & refill) · Exhaust System Heat Shield (inspect) · Fuel Filter (replace) · Parking Brake System (inspect)
At 45,000 miEngine Coolant System (drain, flush & refill)
Every 60,000 miTransfer Case Assembly (drain & refill) · Wheel Bearing (inspect)
Every 100,000 miAccessory Drive Belt (inspect) · PCV Valve (replace) · Spark Plugs (replace)

Common OBD-II trouble codes

The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.

P0420
Catalyst system efficiency below threshold — Bank 1
P0300
Random / multiple cylinder misfire detected
P0171
System too lean — Bank 1
P0455
Evaporative emission system leak detected — large leak
P0128
Coolant thermostat below regulating temperature
P0442
Evaporative emission system leak detected — small leak

VIN tools

Decode factory build data for a specific vehicle by VIN.

VIN
Decode a VIN to confirm the transmission and build data for a specific F-Series B-Series. OEM
Build data
Plant, GVWR class, engine and body data for any 17-character VIN.
Recalls
Check open recall campaigns against a specific vehicle by VIN.

Vehicles with shared specs

Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.

Group 59 batteryVehicles taking 6.0 qt

Reference guides

Cross-vehicle references for the kinds of data on this page.

OBD-II trouble codesTorque specificationsMaintenance schedulesFluid capacities & specs

Frequently asked

How much oil does the 1999 F-Series B-Series take?

6.0 qt of 5W-20 API, per the factory manual.