ChryslerLaser19922.5L/chrysler/laser/1992/2-5l/
AG platform

1992 Chrysler Laser — 2.5L

Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 1992 Laser 2.5L.

Engine 2.5L

The 1992 Chrysler Laser 2.5L. It takes 4.5 qt w/ filter of 15W-40 engine oil.

Quick specs

Fluid capacities, tune-up values and fuel economy at a glance.

Engine oil capacity4.5 qt w/ filterOEM · verified
Engine oil type15W-40 / 10W-30 / 5W-30OEM · verified

Service quick specs OEM factory data

Capacities, torques and tune-up values from the factory service manual.

This engine holds 4.5 qt w/ filter of 15W-40 / 10W-30 / 5W-30 engine oil.

Lubricants & capacities

Engine Oil15W-40 · 10W-30 · 5W-30
Engine Oil Capacity4.5 qt w/ filter

Ignition

Curb Idle Speed (No Load)700 rpm
Curb Idle Speed Variance (No Load)100 rpm

Factory maintenance schedule OEM · verified

Normal service, condensed from the factory interval matrix.

Under the factory schedule, replace the engine oil and filter every 7,500 mi; spark plugs every 30,000 mi; coolant every 30,000 mi. The big-interval services (every 30,000 mi for coolant, and the transmission fluid) are the ones owners most often skip — on a lower-mileage example, assume the original fluids are still in it and check them first.

Every 7,500 miBrake Hydraulic System (inspect fluid level) · Brake Line (inspect) · CV Joint Boot (inspect) · Engine Oil (drain & refill) · Exhaust System (Complete) (inspect) · Fuel Line (inspect)
Every 15,000 miAccessory Drive Belt (inspect) · Engine Oil Filter (replace)
Every 22,500 miBrake Linings (inspect) · Wheel Bearing (inspect)
Every 30,000 miAir Bag System (inspect) · Engine Air Filter Element (replace) · Engine Coolant System (drain, flush & refill) · Spark Plugs (replace)
At 52,500 miEngine Coolant System (drain, flush & refill)

Owner how-tos

Condensed service procedures for routine maintenance. Procedures that require dealer diagnostic equipment are identified and summarized only.

Common procedures

Key fob — remote (RKE) programming programming new fob buttons Dealer tool OEM · verified
Tool requiredDRBIII scan tool (dealer / locksmith)
WhyTransmitter codes are written into the receiver in the passenger door module
Anti-theft (SKIS) — module initialization after immobilizer module replacement Dealer tool OEM · verified
When neededAfter Sentry Key Immobilizer Module (SKIM) replacement
Tool requiredDRBIII scan tool
Also requiredThe vehicle's four-digit PIN code

Common OBD-II trouble codes

The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.

P0420
Catalyst system efficiency below threshold — Bank 1
P0300
Random / multiple cylinder misfire detected
P0171
System too lean — Bank 1
P0455
Evaporative emission system leak detected — large leak
P0128
Coolant thermostat below regulating temperature
P0442
Evaporative emission system leak detected — small leak

VIN tools

Decode factory build data for a specific vehicle by VIN.

VIN
Decode a VIN to confirm the transmission and build data for a specific Laser. OEM
Build data
Plant, GVWR class, engine and body data for any 17-character VIN.
Recalls
Check open recall campaigns against a specific vehicle by VIN.

Vehicles with shared specs

Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.

Reference guides

Cross-vehicle references for the kinds of data on this page.

Frequently asked

How much oil does the 1992 Laser 2.5L take?

4.5 qt w/ filter of ABOVE 20 degrees F 30W SJ, SL, ABOVE 10 degrees F 15W-40 SJ, SL, ABOVE 0 degrees F 10W-30 SJ, SL, BELOW 32 degrees F 5W-30 SJ, SL, BELOW 100 degrees F 5W-30 SJ, SL, per the factory manual.