Chevrolet›Suburban 4WD›2006›Overview/chevrolet/suburban-4wd/2006/base/

2006 Chevrolet Suburban 4WD

Factory specifications, fluid capacities, torque values, EPA fuel economy and the federal safety record for the 2006 Suburban 4WD.

The 2006 Chevrolet Suburban 4WD is specified to take 6 quarts of 5W‑30 API engine oil. Owner‑reported data show it generated 56 total complaints, with service brakes the leading issue and a single recall recorded. Viewed against the model’s complaint history from 1990‑2024—where the peak was 1,004 complaints in 1994 and the trough fell to 37 complaints in 2024—the 2006 year sits well below average, indicating a relatively reliable point in the Suburban’s long‑term record.

Model year2013 2012 2006 2005 1992

Quick specs

Fluid capacities, tune-up values and fuel economy at a glance.

Engine oil capacity6 qtOEM · verified

Engine oil type5W-30 APIOEM · verified

Lug nut torque140 ft-lbsOEM · verified

Fitment & sizes

Replacement part sizes and factory part numbers — battery, bulbs, filters and belts.

From the factory this vehicle uses a BCI 78 · 600 CCA battery, OE oil filter 12731172. Each part links to every other vehicle that shares it, so a part you already stock may fit more of your fleet than you'd expect.

Battery groupBCI 78 · 600 CCAOEM · verified

Tire size265-70R16OEM · verified

OE service part numbers OEM · verified

Engine oil filter	12731172
Engine air filter	22845992 alt 15908916
Spark plug	12621258
Battery	88866305 alt 88865311
Front wiper blades	15214346 alt 10375583
Serpentine belt	12576447 alt 12637202
Thermostat	12600171 alt 12570307

Full specifications

Engine, drivetrain, dimensions and economy.

Dimensions & weight NHTSA vPIC

Overall length	219.3 in
Overall width	78.7 in
Overall height	74.8 in
Wheelbase	129.9 in
Curb weight	5505 lb
Track (front / rear)	65 / 66.1 in
Weight distribution (front / rear)	53/47

Service quick specs OEM factory data

Capacities, torques and tune-up values from the factory service manual.

This engine holds 6 qt of 5W-30 API engine oil, SAE 75W · SYNTHETIC in the differential, DOT 3 brake fluid. Torque lug nuts to 140 ft-lbs, the oil drain plug to 21.0 ft-lbs. The firing order is 1-8-7-2-6-5-4-3. Note the cylinder-head bolts finish on a torque angle (torque-to-yield) — they stretch permanently and should be replaced, not reused, during any head service.

Lubricants & capacities

Automatic Transmission Fluid	ATF
Automatic Transmission Fluid Capacity	7.4
Brake Fluid	DOT 3
Differential Gear Oil	SAE 75W · SYNTHETIC
Differential Gear Oil Capacity	5.5 qt
Differential Gear Oil	SAE 75W · SYNTHETIC
Differential Gear Oil Capacity	4.2 qt
Differential Gear Oil	SAE 75W · SYNTHETIC

Engine torques

Crankshaft Pulley and/or Damper Bolts	189 ft-lbs
Exhaust Manifold to Cylinder Head Bolts	Bolts: 26 ft-lbs, nuts: 12 ft-lbs
Engine Oil Pan Drain Plug	18.0 ft-lbs
Engine Oil Pan Drain Plug	18.0 ft-lbs
Engine Oil Pan Drain Plug	18.0 ft-lbs
Engine Oil Pan Drain Plug	21.0 ft-lbs
Engine Valve Cover Bolts	9.0 ft-lbs
Engine Valve Cover Bolts	9.0 ft-lbs

Chassis torques

Leaf Spring to Chassis Bracket	110.0 ft-lbs
Leaf Spring to Rear Shackle	70.0 ft-lbs
Leaf Spring Rear Shackle to Chassis Bracket	70.0 ft-lbs
Lug Nuts	140 ft-lbs
Front Wheel Hub	177 ft-lbs

Ignition

Cylinder Firing Order	1-8-7-2-6-5-4-3
Spark Plug Manufacturer	AC Delco
Spark Plug Gap	0.060 in
Spark Plug Torque	15 ft-lbs
Spark Plug Manufacturer	Ac Delco
Spark Plug Gap	.060 in
Spark Plug Torque	11 ft-lbs
Spark Plug Manufacturer	AC Delco

Battery & A/C

Refrigerant	R134a
Oil Group	PAG
Standard BCI Group Number	78
Standard BCI Cranking Performance	600 cca
Standard BCI Group Number	78
Standard BCI Cranking Performance	600 cca
Optional BCI Group Number	78
Optional BCI Cranking Performance	690 cca

Service checks

Pressure Test	15 psi
Radiator Cap Pressure Relief	15 psi
Thermostat Opening Temperature	188-206 °F
Fuel Pump Pressure Minimum	62.0 psi
Key ON Engine OFF (KOEO)	55-62
RPM	45-59 @ Idle rpm
Key ON Engine OFF (KOEO)	55-62
Fuel Pump Pressure Minimum	62.0 psi

Brakes

Brake Application	WITH RPO JC3, JC4, JH2 / WITH RPO JH6
Torque Caliper to Bracket	80 ft-lbs / 31 ft-lbs
Torque to Knuckle	129 ft-lbs / 122 ft-lbs
Brake Application	WITH RPO JC3, JC4, JH2 / WITH RPO JH6
Torque Caliper to Bracket	80 ft-lbs / 31 ft-lbs
Torque to Knuckle	129 ft-lbs / 122 ft-lbs
Minimum Pad Thickness	Front: 0.030; Rear: 0.030 specification
Brake Application	WITH RPO JC3, JC4, JH2 / WITH RPO JH6

Multi-step torque procedures OEM · verified

Cylinder Head — tightening sequence 3 stages

Prep M11 bolts:

1	22 ft. lbs.	22 ft. lbs
2	90 degrees	90 degrees
3	70 degrees; M8 bolts: 22	70 degrees

Intake Manifold to Engine Bolts — tightening sequence 1 stages

3.7 ft. lbs., step 2: 7.4

3.7 ft. lbs

Exhaust Manifold to Cylinder Head Bolts — tightening sequence 1 stages

11 ft. lbs., step 2: 18

11 ft. lbs

Intake Manifold to Engine Bolts — tightening sequence 1 stages

3.7 ft. lbs., step 2: 5.9 ft. lbs., step 3: 8.8

3.7 ft. lbs

Factory maintenance schedule OEM · verified

Normal service, condensed from the factory interval matrix.

Under the factory schedule, replace the spark plugs every 100,000 mi; coolant at 150,000 mi. The big-interval services (at 150,000 mi for coolant, and the transmission fluid) are the ones owners most often skip — on a lower-mileage example, assume the original fluids are still in it and check them first.

Every 25,000 mi	Exhaust System (Complete) (inspect) · Fuel System (inspect)
Every 50,000 mi	Engine Air Filter Element (replace) · Fuel Evaporative Emission Control System (inspect) · Transfer Case Assembly (drain & refill)
Every 100,000 mi	Spark Plug Wires (inspect) · Spark Plugs (replace) · Transmission Fluid & Filter (replace)
At 150,000 mi	Accessory Drive Belt (inspect) · Engine Coolant System (drain, flush & refill)

Reliability & federal safety record

Owner-reported issues, recalls, investigations and service bulletins on record with NHTSA — an unfiltered look at what owners actually experience.

Owner complaints about the 2006 Chevrolet Suburban 4WD top in one area — the service brakes, 9 of 56 reports (16%), well ahead of the next concern. None of this vehicle's 1 recall campaigns target the service brakes, so those reports read as owner-reported wear-and-tear rather than an acknowledged defect. 1 of the reports describe a crash and 3 a fire — a small share of the total, but worth weighing against the service brakes pattern above. These are tallies of what owners actually reported to the federal government, not an editorial score — and higher-selling models naturally rack up more reports.

Open recalls

NHTSA campaigns

Service bulletins

Manufacturer communications

ODI investigations

Office of Defects Investigation

Owner complaints

1 involved a crash · 3 a fire

Owner complaints by model year NHTSA · this generation & adjacent

’90 ’91 ’92 ’93 ’94 ’95 ’96 ’97 ’98 ’99 ’00 ’01 ’02 ’03 ’04 ’05’06’07 ’08 ’09 ’21 ’22 ’23 ’24

Owner complaints filed with NHTSA, by component

All 56 complaints on record, top 8 components.

Service Brakes9

Structure9

Latches/Locks/Linkages7

Electrical System6

Air Bags3

Unknown Or Other2

Electrical System,Structure2

Power Train2

Source: NHTSA Office of Defects Investigation complaint database.

Recalls NHTSA · verified

Showing 1 of 1 campaigns on record for this vehicle.

05V552000Equipment:Other:LabelsReported 07/12/2005

CERTAIN TRUCKS AND SPORT UTILITY VEHICLES FAIL TO CONFORM TO THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SHIPPED WITH TIRE AND LOADING INFORMATION… Remedy: OWNERS WILL BE PROVIDED WITH CORRECTED LABELS AND INSTALLATION INSTRUCTIONS. AT THE CUSTOMER'S OPTION, A DEALER CAN INSTALL THE LABEL FOR THEM. THE RECALL BEGAN ON MARCH 31, 2006…

Common OBD-II trouble codes

The most common OBD-II codes for this vehicle's emissions system. These are standardized SAE J2012 definitions, not vehicle-specific fault reports.

P0420

Catalyst system efficiency below threshold — Bank 1

P0300

Random / multiple cylinder misfire detected

P0171

System too lean — Bank 1

P0455

Evaporative emission system leak detected — large leak

P0128

Coolant thermostat below regulating temperature

P0442

Evaporative emission system leak detected — small leak

VIN tools

Decode factory build data for a specific vehicle by VIN.

VIN

Decode a VIN to confirm the transmission and build data for a specific Suburban 4WD. OEM

Build data

Plant, GVWR class, engine and body data for any 17-character VIN.

Recalls

Check open recall campaigns against a specific vehicle by VIN.

Vehicles with shared specs

Find every vehicle that shares this one's battery, bulbs, oil capacity, platform or parts.

Group 78 battery Vehicles taking 6 qt Engine oil filter 12731172 Engine air filter 22845992 Spark plug 12621258 Battery 88866305

Reference guides

Cross-vehicle references for the kinds of data on this page.

Vehicle recalls & TSBs OBD-II trouble codes Torque specifications Maintenance schedules Fluid capacities & specs

Frequently asked

How much oil does the 2006 Suburban 4WD take?

6 qt of 5W-30 API, per the factory manual.

Does the 2006 Suburban 4WD have open recalls?

NHTSA lists 1 recall campaign(s) for this model year. Check your specific vehicle by VIN.